Click here to return to the HomePage. Click here for Sales information. Click here for Service. Click here to see our Products. Click here to see our Featured Products. Click here to order Supplies. Click here for a brief Company Profile. Click here to Contact Us.

DASH 3000 Specifications

Display
  • Size: 10.4-inch (diagonal) 
  • Type: Active-matrix color LCD
  •  Resolution: 640 by 480 pixels 
  • Number of traces: 6 (maximum)
  •  Number of seconds/trace: 4.9 at 25 mm/sec 
  • Sweep speed: 6.25,12.5,25 mm/sec (with erase bar) 
  • Information window: Displays non-real-time information without obstructing the display of real-time information 
  • Display organization: Prioritized by parameter

    CONTROLS
    Trim Knob' control
  • Five hard keys: Silence Alarm, Graph Go/Stop, NBP Go/Stop, Function (zero a 11) and Power
    On/Off

    ALARMS
  • Categories: Patient status and system status 
  • Priority: 4 levels - Crisis, Warning, Advisory, Message 
  • Notification: Audible and visual 
  • Setting: Default and individual 
  • Silencing: 1 minute, current alarm only
  •  Pause: 5 minutes in Adult ICU mode, 3 minutes in Neonatal ICU mode, and 5 minute, 15 minute, or permanent pause in OR mode 
  • Volume: Default 70%,70 dB measured at 1 meter

    ECG
  • Standard leads available: I, II, III, V, aVR, aVL, and aVF 
  • 10 leadwire cable: I, II, III, V, aVR, aVL, aVF, V2, V3, V4, V5, V6 
  • Leads analyzed simultaneously: 1, 11, 111, and V (multi-lead mode) 
  • Lead fail: Identifies failed lead 
  • Alarms: User-selectable upper and lower heart rate limits

    Input specifications
  • Voltage range: ± 0.5 mV to ± 5 mV
  • Signal width: 40 ms to 120 ms (Q to S)
  • Heart rate range: 30 to 300 bpm
  • Input impedance:
    - Common mode: > 10 M ohms at 50/60 Hz
    - Differential:> 2.5 M ohms from dc to 60 Hz
  • Common mode rejection: 90 dB minimum at
    50 or 60 Hz

    Output specifications
  • Frequency response:
  • Display: Diagnostic: 0.05 to 40 Hz
    - Monitoring: 0.05 to 40 Hz
    - Moderate: 0.05 to 25 Hz
    - Maximum: 5 to 25 Hz
  • Paper
  • Recorder: Diagnostic: 0.05 to 100 Hz
    - Monitoring: 0.05 to 40 Hz
    - Moderate: 0.05 to 25 Hz
    - Maximum: 0.05 to 25 Hz
  • Noise: < 30 uV (referred to input)

    Pacemaker detection/rejection
  • Input voltage range: ± 2 mV to ± 700 mV
  • Input pulse width: 0.1 ms to 2 ms
  • Rise time: 10 us to 100 us
  • Over/under shoot: 2 mV (max)
  • Baseline drift: < 0.5 mV per hour with a 700 mV, 2-ms pacemaker pulse applied

    RESPIRATION
  • Measurement technique: Impedance variation detection 
  • Range: Respiration rate: 0-200 breaths per minute 
  • Base impedance: 100- 1000ohms at 52.6 kHz 
  • Detection sensitivity: 0.4 to 10 ohms variation 
  • Waveform display bandwidth: 0.1 to 1.8 Hz (-3 dB) 
  • Alarms: User-selectable upper and lower respiration rate limits, and user-selectable apnea limit

    Temperature
  • Number of channels: 2
    Input specifications
  • Probe type: YSI Series 400 or 700
    (determined by input cable)
  • Temperature range: O'C to 45'C (32'F to 113'F)
  • Resolution: ± 0.1'C
    Output specifications
  • Parameters displayed: T1, T2
  • Accuracy: (independent of source) ± 0. 1'C for YSI series 400 probes-, ± 0.3'C for YSI series 700 probes
  • Alarms: User-selectable upper and lower limits for T1, T2

    INVASIVE BLOOD PRESSURE
  • Number of channels.- 2 (optional)
  • Transducer sites: Arterial, femoral artery, pulmonary arterial, central venous, right atrial, left atria], intracranial, and special
  • Transducer requirements:
    Excitation voltage: 5 V dc ± 0.1 %
    Transducer output: 5 uV/V/mmHg
  • Input specifications
    Range: -25 mmHg to 300 mmHg
  • Offset: ± 150 mmHg
    Output specifications
  • Frequency response: dc to 50 Hz (-0/+2 Hz) 
  • Zero balance range: ± 150 mmHg 
  • Zero balance accuracy: ± 1 mmHg
  • Zero balance drift: ± 1 mmHg over 24 hours 
  • Accuracy: ± 2% or± 1 mmHg, whichever is greater (exclusive of transducer) 
  • Alarms: User-selectable upper and lower limits for systolic, diastolic, and mean pressures


  • WIRELESS LAN SYSTEM
  • Operating Frequency: 2.4 to 2.5 G Hz
  • Transit Power: 100 mW 
  • Data Rate: 1 Mbps and 2Mbps per channel 
  • Radio Technology: Frequency-hopping spread spectrum 
  • Communication Protocol: IEEE 802.11
  • UL 1950 Listed (ITE 9B97), CE Mark
  • RF Standard 
  • US: FCC Part 15 Class B, Europe: ETS 300 328 and ETS 300 826

    ENVIRONMENTAL SPECIFICATIONS 
  • Power requirements:
    - 90-132 VAC       50/60 Hz 2.0A
    - 190-264 VAC     50/60 Hz 1.0A
  • Power consumption: 75 W (f ully loaded)
  • Cooling: convection
  • Heat dissipation: 240 Btu/hr (max)
    OPERATING CONDITIONS
  • Ambient temperature: 0-40'C (32-104'F) While charging batteries: 0-35'C (32-95'F) 
  • C02 Sensor: 10-40'C (59-104'F)
  • Relative humidity: 5-95% @40'C
  • Vibration: MIL-STD 810E, Method 514.4, Category 1 
  • Altitude: -610 to 4.570 m (-2,000 to 15,000 ft.)
    STORAGE CONDITIONS
    (do not exceed):
  • Maximum: 70'C (1 58'F) at 95% relative humidity
  • Minimum: -40'C (-40'F)
  • C02 Sensor: -30 to 65'C (-22 to 149'F)
  • Batteries: -20 to 60'C (-4 to 140'F)
    PHYSICAL SPECIFICATIONS
    Height: 27.4cm(10.8 in)
    Depth: 24.3 cm (9.6 in)
    Width: 29.3 cm (11.5 in)
    We i g ht: 5.5 kg (12.2 l b)

 DINAMAP
NONINVASIVE BLOOD PRESSURE
  • Measurement technique: Oscillometric
  • Displayed parameters: Systolic, diastolic, and mean pressures, time of last measurement 
  • Measurement modes: Manual, auto, and stat in Adult ICU and OR modes; manual and auto in neonatal mode
  • Measurement range(s): Resolutions of 5 mmHg up to Maximum Adult/Pediatric/ Neonate limits
    Systolic:
  • Adult: 30-275mmHg
  • Pediatric: 30-235mmHg
  • Neonate: 30-135mmHg
    MAP:
  • Adult: 20-260mmHg
  • Pediatric: 20-260mmHg
  • Neonate: 20-125mmHg
    Diastolic:
  • Adult: 10-220mmHg
  • Pediatric: 10-220mmHg 
  • Neonate: 10-110mmHg
    Pulse rate, as displayed in Vital Signs window:
  • Adult: 30-200 bpm
  • Pediatric: 30-200 bpm 
  • Neonate: 30-200 bpm
    Cuff pressure range:
  • Adult: 0-275mmHg
  • Pediatric: 0-235mmHg 
  • Neonate: 0-1 35mmHg 
  • Overall system accuracy: Meets or exceeds SP 10-1992 AAMI standards
  • Total cycle time: 20 to 40 seconds typical
    (dependent on heart rate and motion artifact) 
  • Automatic cycle times: 0 to 8 hours
  • Tubing length: 12 feet adult, 8 feet neonatal 
  • Automatic cuff deflation: Cycle time exceeding 3 minutes (90 seconds neonatal), power off, or cuff pressure exceeds 294 mmHg (±6 mmHg) adult, 147 (±3 mmHg) neonatal
    Cuff sizes
  • Disposable: Large adult, adult, small adult pediatric, small pediatric, and infant 
  • Reusable: Thigh, large adult, adult, child, and infant
  • Alarms: User-selectable upper and lower limits for systolic, diastolic, and mean pressures
    CARDIAC OUTPUT

    Input specifications
  • Probe type: In-Line or bath probe
  • Catheter size: 5F, 6F, 7F, 7.5F, and 8F
  • Injectate volume: 3, 5, or 10 cc
    Output specifications
  • Parameters displayed: Cardiac output, blood temperature, injectate temperature, trial number
  • Range:
     - Cardiac output: 0.2- 15(liters per minute) 
    -Blood temperature: 30-42'C 
    - Injectate temperature: 0-30'C
  • Accuracy 
    - Cardiac output: ± 5% 
    - Blood temperature: ± 0.2'C 
    - Injectate temperature: ± 0.3'C
  • Frequency response: dc to 15 Hz ± 2 Hz

    PULSE OXIMETRY
  • Parameters monitored: Arterial oxygen saturation (SpO2) and peripheral pulse rate PPR)
  • SP02 range: 50 - 100%
  • PPR range: 30 - 300 beats per minute
  • Accuracy: Actual accuracy depends on probe. Please reference manufacturer's specifications.
  • SP02:± 2% (70 - 100% SP02); ± 3% (50 - 69% SP02)
  • PPR: ± 3 beats per minute
  • Alarms: User-selectable upper and lower limits for SP02 and PPR

    CO2
    Information displayed
    Inspired and expired C02 concentrations in %, mmHg, or kPa; respiratory rate, continuous C02 waveform
    Measurement range
  • Pi CO2/Fi C02: 0 to 100 mmHg / 0 to13%
  • Pe C02/ Fe C02: 0 to 100 mmHg / 0 to 13%
  • RR: 0 to 120 breaths/min
    Accuracy
  • C02- 5% of reading or ±2 mmHg, whichever is greater
  • Display resolution: 1 mmHg
  • Rise time: Less than 60 msec
  • Respiration rate accuracy: ±1 breath/min
    Compensations
  • 02/N20 compensation: Operator selectable
  • Barometric pressure compensation: Automatic

    Performance Specifications

    Technology
    Type: Novametrix Medical Systems' CAPNOSTAT III
  • Sensor: Mainstream non-dispersive infrared (NDIR) absorption, dual wavelength ratiometric, true single beam optics.
  • Warm-up time: 2 minutes warm-up time to meet accuracy specifications; waveform immediate upon power up, calculated end tidal after two breaths
    Cable Length: 10 feet (3.0 m)
    Calibration
    Simple one-step calibration,- no calibration gases required.
    Airway adapters
  • Types: Adult reusable (standard), adult disposable, neonatal
  • Deadspace/chamber volume: 
    -Adult reusable: <5 cc 
    -Adult disposable:< 5 cc 
    - Neonata I: < 0.5 cc
    Alarms
  • C02: High inspired C02; high/low expired C02
  • Respiratory rate: Adjustable high and low

    PAPER RECORDER
  • Method: Thermal dot array
  • Horizontal resolution: 480 dots/in @ 25 mm/sec
  • Vertical resolution: 200 dots/in
  • Number of waveform channels: four
  • Paper width: 50 mm (1.97 in)
  • Paper length: 30 rn (100 ft)
  • Paper speed: 0.1, 0.5,1, 5,10,12.5, 25, and 50 mm/sec (±2%)

    ANALOG OUTPUT
    ECG
  • Gain:1 V/mV±10%
  • DC offset: ± 100 mV (max)
  • Noise: < 5 mV peak to peak 0 - 300 Hz
  • Frequency response: 0.05 Hz to 100 Hz - 0/+7 Hz
    Blood pressure
  • Gain: 10 mV/mmHg ± 2%
  • DC off set: ± 20 mV (max)
  • Noise: < 5 mV peak to peak 0 - 300 Hz
  • Frequency response: dc to 50 Hz - 0/+2 Hz
    BATTERY
  • Battery type: Exchangeable Lithium-ion
  • Maximum number of batteries: 2
  • Voltage: 11.1 V (nominal)
  • Capacity: 3.9 Ah
  • Charge time: Less than 4 hours each
  •  Run time: 4 to 5 hours
  • Battery life: 500 cycles to 50% capacity
    CERTIFICATION
  • UL2601-1 classified.
  • UL classified for CAN/CSA C22.2 No. 601.1
  • IEC 60601 -1 certified.
  • CE Marking for the 93/42/EEC Medical Device Directive.

OPTIONS

  • Sam Module   Sam80=A           Call for pricing
    CO2 and Anesthetic Agent Analysis

    RAC 2A Module Housing TR2P=A    Call for pricing
    Required for SAM Module

  • SAM Module    SAM=A            Call for pricing
    CO2, O2 and Anesthic Agent Analysis

    RAC 2A Module Housing TR2P=A    Call for pricing
    Required for SAM Module

    The SAM Module requires the following:
    Module Housing Cable - 700179-001    Call for pricing

Start-Up Kit

Start-Up Kit includes:

  • ECG Standard Cable, AHA                                E9002ZB

  • 5 Leadwire Set, Snap. Short (29 in),
    AHA                                                                  E9003CR

  • NBP Tubing, Adult, 12 ft.                                   E9001TC

  • Adult Reusable NBP Cuff,
    Range 25 - 35 cm                                               E9001SM

  • 8 in. Temperature Cable for use with
    REUSABLE Temperature Probe                        E9004ZM

  • Nellcor/EAGLE Interface Cable (8 ft.).
    Includes 3 Disposable Adult Oxisensors              E9004DE



Home Page