Click here to return to the HomePage. Click here for Sales information. Click here for Service. Click here to see our Products. Click here to see our Featured Products. Click here to order Supplies. Click here for a brief Company Profile. Click here to Contact Us.

DASH 2000 Specifications

Display
  • Size: 5.8-inch (16 cm) (diagonal)
  • Type: Monochrome LCD; optional color LCD
  • Resolution: 320 by 240 pixels
  • Number of traces: 3
  • Number of seconds/trace: 3.8 at 25 mm/sec
  • Sweep speed: 25 mm/sec (with erase bar)
  • Information window: Displays non-real-time information without obstructing the display of real-time information
  • Display organization: Prioritized by parameter

    CONTROLS
    Trim Knob' control
  • Five hard keys: Silence Alarm, Graph Go/Stop, NBP Go/Stop, Function and Power On/Off

    ALARMS
  • Categories: Patient status and system status
  • Priority: 4 levels - Crisis, Warning, Advisory, Message
  • Notification: Audible and visual
  • Setting: Default and individual
  • Silencing: 1 minute, current alarm only
  • Pause: 5 minutes in Adult ICU mode, 3 minutes in Neonatal ICU mode, and 5 minute, 15 minute, or permanent pause in OR mode
  • Volume: Default 70%, 70 dB measured at 1 meter

    ECG
  • Standard leads available: I, II, III, V, aVR, aVL and aVF
  • Leads analyzed simultaneously: I, II, III and V (multi-lead mode)
  • Lead fail: Identifies failed lead
  • Alarms: User-selectable upper and lower heart rate limits

    Input specifications
  • Voltage range: ± 0.5 mV to ± 5 mV
  • Signal width: 40 ms to 120 ms (Q to S)
  • Heart rate range: 30 to 300 bpm

    Input impedance
  • Common mode: > 10 M ohms at 50/60 Hz
  • Differential: > 2.5 M ohms from dc to 60 Hz
  • Common mode rejection: 90 dB minimum at 50 or 60 Hz

    Output specifications
    Frequency response:
  • Display:
    - Diagnostic: 0.05 to 40 Hz
    - Monitoring: 0.05 to 40 Hz
    - Moderate: 0.05 to 25 Hz
    - Maximum: 5 to 25 Hz
  • Paper Recorder:
    - Diagnostic: 0.05 to 100 Hz
    - Monitoring: 0.05 to 40 Hz
    - Moderate: 0.05 to 25 Hz
    - Maximum: 0.05 to 25 Hz
  • Noise: < 30 uV (referred to input)

    Pacemaker detection/rejection
  • Input voltage range: ± 2 mV to ± 700 mV 
  • Input pulse width: 0.1 ms to 2 ms 
  • Rise time: 10 us to 100 us 
  • Over/under shoot: 2 mV (max)
  • Baseline drift: < 0.5 mV per hour with a + 700 mV, 2-ms pacemaker pulse applied

    RESPIRATION
  • Measurement technique: Impedance variation detection
  • Range:
    - Respiration rate: 0 to 200 breaths per minute
    - Base impedance: 100 to 1000 ohms at 52.6 kHz
    - Detection sensitivity: 0.4 to 10 ohms variation
  • Waveform display bandwidth: 0.1 to
    1.8 Hz (- 3dB)
  • Alarms: User-selectable upper and lower respiration rate limits and apnea limit


    INVASIVE BLOOD PRESSURE
  • Number of channels: 1 (optional)
  • Transducer sites: Arterial, pulmonary arterial central venous, left atrial, intracranial and special
  • Transducer requirements:
    - Excitation voltage: ± 2.5V dc±0.1 %
    -Transducer output: 5uV/V/mm Hg
  • Input Specifications:
    - Range: - 25 mm Hg to 300 mm Hg
    -Offset: ± 150 mm Hg
  • Output Specifications:
    - Frequency response: dc to 50 Hz (+ 0/1 to 2 Hz)
    -Zero balance range: ± 150 mm Hg
    -Zero balance accuracy: ± 1 mmHg
    -Zero balance drift: ± 1 mm Hg over 24 hours
    - Common mode rejection: >60 dB at 60 Hz
    - Noise: < 0.2 mm Hg (peak to peak)
    - Accuracy: 2% on 1 mm Hg (in the range of -25 mm Hg to 350 mm Hg) whichever is greater (exclusive of transducer)
  • Alarms: User-selectable upper and lower respiration rate limits and apnea limit
  • Alarms: User-selectable upper and lower limits for systolic, diastolic and mean pressures

 TEMPERATURE
  • Number of channels: 1

    Input specifications
  • Probe type: YSI Series 400
  • Temperature range: 0'C to 45'C (32'F to 113'F)
  • Resolution: ± 0.1 'C (.1 8'F)

    Output specifications
  • Parameters displayed: TP
  • Accuracy: (independent of source) ± 0.1 'C (.18'F)
  • Alarms: User-selectable upper and lower limits

    NONINVASIVE BLOOD PRESSURE
  • Measurement technique: Oscillometric
  • Displayed parameters: Systolic, diastolic and mean pressures, pulse rate, time of last measurement
  • Measurement modes: Manual, auto and stat in Adult ICU and OR modes; manual and auto in neonatal mode
  • Heart rate detection: 30 to 300 beats per minute
  • Total cycle time: 20 to 40 seconds typical (dependent on heart rate and motion artifact)
  • Automatic cycle times: 0 to 24 hours
  • Auto zero: Zero pressure reference prior to each cuff inflation
  • Tubing length: 12feet(366 cm) adult, 8feet (244 cm) neonatal
  • Automatic cuff deflation: Cycle time exceeding 3 minutes (90 seconds neonatal), power off, or cuff pressure exceeds:
    - 294 mm Hg 6 mm Hg) adult, 
    - 147 mm Hg 3 mm Hg) neonatal

    Cuff sizes:
  • Disposable: Pediatric, small pediatric and infant 
  • Reusable: Thigh, large adult, adult, child and infant 
  • Alarms: User-selectable upper and lower limits for systolic, diastolic and mean pressures 
  • Pressure accuracy (static): ± 2% or± 3 mm Hg, whichever is greater 
  • Pressure accuracy (clinical use): ± 5 mm Hg average error 8 mmHg standard deviation

    PULSE OXIMETRY
  • Parameters monitored: Arterial oxygen saturation (SP02) and peripheral pulse rate (PPR)
  • SP02 range: 50 to 100%
  • PPR range: 30 to 300 beats per minute
    (± 3 beats per minute)
  • Accuracy: Actual accuracy depends on probe.
    Please reference manufacturer's specifications.
    SP02:
    ± 2% (70 to 100% SP02)
    ± 3% (50 to 69% SpO2)
  • PPR: ± 3 beats per minute
  • Alarms: User-selectable upper and lower limits for SP02 and PPR

    PAPER RECORDER(OPTIONAL)
  • Method: Thermal dot array
  • Horizontal resolution: 480 dots/in @25 mm/sec
  • vertical resolution: 200 dots/in
  • Number of waveform channels: 3
  • Paper width: 50 mm (1.97 in)
  • Paper length: 25 m (95 ft)
  • Paper speed: 0.1, 0.5,1, 5,10,12.5, 25 and 50 mm/sec (± 2%)

    ANALOG OUTPUT
    ECG
  • Gain: 1 V/mV ±10%
  • DC offset: ± 100 mV (max)
  • Noise: < 5 mV peak to peak dc to 300 Hz
  • Frequency response: 0.05 Hz to 100 Hz -0/+7 Hz

    INTERNAL BATTERY
  • Battery type: Nickel-cadmium (Ni -Cd)
  • Charge time: 1 to 4 hrs 
    Run time: 3 to 4 hrs

    ENVIRONMENTAL
    SPECIFICATIONS
  • Power requirements:
  • 90 to 264 VAC 50/60 Hz 500 mA
  • Power consumption:
  • 40 W (f ully loaded)
  • Cooling: convection
  • Heat dissipation: 135 Btu/hr (max)

    OPERATING CONDITIONS
  • Ambient temperature: 10 to 40'C (50 to 104'F)
  • Relative humidity: 5 to 95% @ 40'C (104'F)
    STORAGE CONDITIONS
    (do not exceed):
  • Temperature: - 25'C to 70'C (- 13'F to 156'F)
  • Relative humidity: 15 to 95%

    PHYSICAL SPECIFICATIONS
    Height: 26 cm (10.25 in)
    Depth: 20 cm (8 in)
    Width: 28cm(11.0 in)
    Weight: 5.5 kg (12 lb) with all options

    CERTIFICATION
  • UL2601 -1 classified. 
  • UL Classified for CAN/CSA C22.2 No. 601.1. 
  • IEC 60601 -1 certified. 
  • CE Marking for the 93/42/EEC Medical Device Directive.

    WARRANTY
    MONITOR
  • Standard warranty is one year.
  • Other options are available.

Start-Up Kit

Start-Up Kit includes:

  • ECG Standard Cable, AHA                                E9002ZB

  • 5 Leadwire Set, Snap. Short (29 in),
    AHA                                                                  E9003CR

  • NBP Tubing, Adult, 12 ft.                                   E9001TC

  • Adult Reusable NBP Cuff,
    Range 25 - 35 cm                                               E9001SM

  • 8 in. Temperature Cable for use with
    REUSABLE Temperature Probe                        E9004ZM

  • Nellcor/EAGLE Interface Cable (8 ft.).
    Includes 3 Disposable Adult Oxisensors              E9004DE


Home Page